You tin can't turn a blind eye on your leaking garden hose connector any longer. Yous might think you're holding that connector in place by the sheer forcefulness of your will and determination. You're non and it won't be long now before you lot accept to deal with more than than merely a leaky connector.

It might be that it really is time to turn in your old hose connector for a new 1. They're cheap enough, and any hardware store you visit volition carry i to suit your needs.

Simply before y'all practice that, allow'southward bank check under the hood first, or connector head, as the case is to find out exactly why it'due south leaking and what you can practice to fix it.

Here's how to fix a leaking garden hose connector in one case and for all.

ane. Tighten the connector

Turn off the water. Yous'd be surprised how many people forget to practise this. Let's take it for granted that this should be the first affair you practice every time you remove your hose.

Check the blazon of connector you have. Nigh connectors you'll discover will be the universal, standard connector. Simply sometimes, your connector might exist unlike, so it never hurts to check.

These connectors either come with a rubber turner or a stainless steel prune fastened that you'll need to tighten when you set up it to your tap.

The well-nigh common (and easy-to-set) reason why your hose connector might be leaking is because of this steel or rubber clip correct hither. They never seem to stay equally tight as when you first screwed them on. Even the best garden hoses accept this issue.

So what's a quick fix to this problem?

First, tighten the rubber mouth or the steel clip around where it'south fixed to the tap. You don't need whatsoever tools merely yet, just your hand to plow that loose connector back in place.

How To Fix A Leaking Garden Hose Connector

But e'er so oft, you'll find that the connector is still leaking. You've checked for any other possible culprit but can't notice anything wrong. Remember how I said you don't need your tools just yet?

Maybe it'due south time yous go grab a wrench. Your connector might merely need a trivial more help being tightened, and a wrench should practise the trick.

A discussion of caution: Remember though, that while tightening a connector on tight isn't bad, but fixing it in place extra-tight, is. Over time, you'll find that your hose is getting deformed. This ways that the hose condom around the connector looks like it'southward being held in a chokehold.

Why? When you tighten information technology extra-tight, the water force per unit area will bear witness too forceful, and the rubber volition slowly expand. Moderation is the fundamental.

two. Leaking from the end of the hose

The cease of your hose, where it meets the connector, tin besides be why y'all're seeing water spurting from the bottom of the connector. Information technology'southward not the connector that is leaking, simply the hose itself.

Why: It might merely be from wearable and tear, or if you've had some extreme atmospheric condition, the cold can freeze the hose as often as the heat tin melt information technology. It might also need a thorough cleaning, only that's easy enough to practise and easier withal to ready.

Detach the hose from the connector fittings, and then remove your hose clip or the safety washer.

If you find it too tight to remove the hose, concur it in warm h2o for a few seconds to soften the rubber. Alternatively, hold the fitting in place between your shoes and gently pull at the hose to pop it off.

Do you see those frayed ends? That correct there could be why your hose connector is leaking.

Take hold of your pliers, preferably one that is big plenty to cutting through the hose. Alternatively, y'all can use a utility knife or a saw from your garden hose kit. Then, remove the washer or hose clamp.

Y'all have to brand sure that you lot trim the damaged edge off evenly. You might observe that it needs more than simply a trim. You tin can cut or clip off a couple of inches back from the edges or back from where you lot run into the impairment to the hose.

Using a utility pocketknife

  1. Keep the hose flat against a difficult surface.
  2. Hold the hose down. Consider using a steady weight to agree it down and place force per unit area on it. This should also keep it in identify while you cut information technology.
  3. Cut through the hose without fraying the rubber or hacking at it.

Using pliers

A pair of thick, standard house pliers volition just as effectively cut the damaged finish off. But if yous happen to have a garden hose kit, you'll definitely discover a hose plier in in that location to exercise the job.

Quick Tip: If you're not besides confident about cutting the hose yourself, and lugging that length of hose is more viable than really sawing the ends, you can have it over to your nearest garden store where they'll be happy to do it for you lot. Information technology just takes a minute and the sharp terminate of a pocketknife.

Put the washer or hose clip dorsum in place and reattach the hose to the connector.

Try turning on the tap. See? All stock-still.

3. Damaged safety washer or gasket

Call back that rubber tube you lot took off your hose to prune it? That's your washer. You'll be surprised how pesky something so small and unassuming can really be.

The most common reason for a leaky hose connector is a bad washer. Sometimes, the washer might be missing altogether. But, once more, this is an easy enough set.

Quick Tip: You tin can buy a dozen or so universal rubber hose washers for a buck, merely sometimes, your hose might need a steel hose clip. Ever check to notice out what your hose needs.

Once y'all accept your new washer or clip, remove the hose from the connector and pull off the old, damaged 1. If you have a steel clip in place, you will demand to employ a flathead screwdriver to remove it.

Another quick tip: You can hold your hose downwardly in some warm water for a few seconds to soften and alternatively clean the head.

Once y'all've done that, information technology should exist easier to slip on the new washer or clip. Secure it in place.

Things to watch out for

  • Before y'all attach the hose with the connector, pay attention to how y'all secure the washer.
  • Ensure that the sleeve goes all the way into the hose and stays there.
  • It also doesn't hurt to ensure that the rubber seal is of good quality and won't requite away all that easy.

If y'all've got a steel clip in place, then you will accept to secure that every bit well. For this, you will need to apply that flathead screwdriver again, or a channel lock, to push down the steel clip and secure information technology in place. Similarly, when you tighten the clamp, make sure you don't accept it in a chokehold merely instead a strong, firm grip.

One time you fix the washer and are confident that it's snug and secure, you tin reattach the hose and clench to the connector.

Plough on the faucet to cheque for any leaks.

Quick Tip: if you notice that the water pressure level is off, there's a expert possibility that you've tightened the clamp or the connector too tight.

So that's information technology! Hopefully y'all won't see anymore leaks. Another common problem is garden hose kinking, it's a skilful idea to prevent kinks and so y'all can keep your hose healthy for years to come.